- Download Ntldr File For Xp
- Download Ntldr File
- Download File Ntldr Ntdetect Com Boot Ini
- Free Download Ntldr File
Below are the full error messages that may be seen when the computer is booting.
On Windows XP, this bootsector code is tasked with loading NTLDR (the Windows XP bootloader) and its dependencies, which are used to load the operating system kernel and start up Windows. The NTLDR file is normally located in the root directory of the active partition on the first boot drive. NTLDR expects NTDETECT.COM to be located in the root of the primary boot partition. Typically, this is the active partition on disk 0. If BIOS configuration has changed, on a system with multiple drives NTDETECT may no longer be on the first boot drive, causing NTLDR to complain that it cannot be found. Cause 2: Changes to the active partition.
Computer is booting from a non-bootable source
Many times this error is caused when the computer is attempting to boot from a non-bootable floppy disk or CD-ROM. First verify that no floppy diskette or CD is in the computer, unless you are attempting to boot from a diskette.
NoteThis error has also been known to occur when a memory card is in a card reader and the computer is attempting to boot from it. If you have any card reader or flash reader, make sure that no memory stick is inside the reader. Additionally, disconnect all USB drives, cameras, ipods, iphones, etc. from the computer.
If you are attempting to boot from a floppy diskette and are receiving this error message, it is likely that the diskette does not have all the necessary files or is corrupt.
If you are attempting to install Windows XP or Windows 2000 and are receiving this error message as the computer is booting, verify that your computer BIOS has the proper boot settings. For example, if you are attempting to run the install from the CD-ROM, make sure the CD-ROM is the first device listed in the boot sequence, instead of the hard drive.
Also, when the computer is booting, you should receive the below prompt:
Press any key to boot from the CD
ImportantDownload Ntldr File For Xp
When you see this prompt, press any key on the keyboard immediately, such as the Enter or Space key. Otherwise, the computer will try booting from the hard drive and likely get the NTLDR error again.
NoteIf you are not receiving the above message and your BIOS boot options are set properly, it's also possible that your CD-ROM drive may not be booting from the CD properly. Verify the jumpers are set properly on the CD-ROM drive.
Computer hard drive is not properly setup in CMOS
Verify that your computer hard drive is properly set up in the CMOS setup. Improper settings can cause this error.
Corrupt NTLDR or NTDETECT.COM file
Windows 2000 users.
Windows XP users.
Windows XP users.
Windows 2000 users
If your computer is using Microsoft Windows 2000 and you are encountering the NTLDR error, create the below boot.ini file on the floppy diskette drive.
Copy the NTLDR and NTDETECT.COM files from another computer using the same operating system. Both of these files are located in the root directory of the primary hard drive. For example, C:NTLDR and C:NTDETECT.COM should be the locations of these files on many computers.
Once these files have been copied to a floppy diskette, reboot the computer and copy the NTLDR and NTDETECT.COM files to the root directory of the primary hard drive. Below is an example of the commands that should be performed from the A:> floppy drive to copy the files.
After the above two files have been copied, remove the floppy diskette and reboot the computer.
Windows XP users
- Insert the Windows XP bootable CD into the computer.
- When prompted to press any key to boot from the CD, press any key on the keyboard.
- Once in the Windows XP setup menu, press the 'R' key to repair Windows.
- Log into your Windows installation by pressing the '1' key and pressing Enter.
- You will then be prompted for your administrator password. Enter that password.
- Copy the below two files to the root directory of the primary hard drive. In the example below, we are copying these files from the CD-ROM drive letter, which in this case is 'e.' This letter may be different on your computer.
- Once both of these files have been successfully copied, remove the CD from the computer and reboot.
Misconfiguration with the boot.ini file
Edit the boot.ini on the root directory of the hard drive and verify it's pointing to the correct location and that the partitions are properly defined.
Attempting to upgrade from a Windows 95, 98, or ME computer that is using FAT32
You may receive this error message when trying to upgrade to Windows 2000 or Windows XP from Windows 95, Windows 98, or Windows ME running FAT32. If so, try the below recommendations.
Download Ntldr File
- Boot the computer with a Windows 95, Windows 98 or Windows ME bootable diskette.
- At the A:> prompt, type sys c: and press Enter.
- After pressing Enter, you should receive the 'System Transferred' message. Once this is completed, remove the floppy diskette and reboot the computer.
New hard drive being added
Photodraw download windows 10. If you are attempting to add a new hard drive to the computer, make sure the drive is a blank drive. Adding a new hard drive to a computer that already has Windows installed on it may cause the NTLDR error to occur.
If you are unsure if the new drive is blank, try booting from a bootable diskette and format the new hard drive.
Corrupt boot sector or master boot record
It's possible your computer's hard drive may have a corrupt boot sector or master boot record. These can be repaired through the Microsoft Windows Recovery Console by running the fixboot and fixmbr commands.
Seriously corrupted version of Windows 2000 or Windows XP
If you have tried each of the above recommendations that apply to your situation and you continue to receive the NTLDR error, there may be a more serious corruption issue in Microsoft Windows. Therefore, we would recommend reinstalling Microsoft Windows.
If you are encountering this issue during your setup, you may want to completely erase your computer hard drive and all its existing data and re-install Microsoft Windows.
Loose or faulty IDE/EIDE hard drive cable
This issue is known to be caused by a loose or defective IDE/EIDE cable. If your hard drive uses an IDE or EIDE interface, check that the computer hard drive cable is firmly connected. Disconnect and then reconnect the cable, making sure that the connection is snug and secure.
If the issue continues, it is also a possibility that the computer has a faulty cable, try replacing the hard drive cable with another cable or a new cable.
Download File Ntldr Ntdetect Com Boot Ini
Bad hard drive
If none of the above suggestions work to resolve the issue, there is a strong possibility the hard drive is bad and needs to be replaced. You can try installing a new hard drive and installing Windows on that hard drive to see if that resolves the issue.
Additional information
Free Download Ntldr File
- See the NTLDR definition for further information and related links.